My first build, used a super helpful PC building guide by a youtuber by the name of Bitwit. Very happy with how this turned out! Luckily for me, the PC turned on first try with no hardware problems or bunged-up installations; however I'm having a bit of trouble with some software in the PC - unlikely anything to do with the components and more-so to do with corrupted OS installation or something. Getting that fixed soon-ish.


Ryzen 5 1600

Heard many good things about this CPU, chose it over Intel as I'm into video editing and photography as well as gaming and figured that Ryzen would give me some boosts in those areas. Mine came with the corner bent slightly, however I installed it normally and my thermals and performance are fine so I think I got lucky.


MSI B350M Mortar

Chose it as I wasn't comfortable going with ASrock due to hearing negative things about the company from friends. The BIOS is easy to use, and the LEDs are pretty good - however you can easily turn them off with the MSI gaming app if red doesn't fit your 'colour scheme'. Installation was pretty easy.


Corsair Vengeance LPX 8gb DDR4-2666

Opted for 2666mhz instead of 3000mhz to shave off a couple bucks at the last minute and downgraded from 16gb to 8gb as I figured I wouldn't need it in the near future and could upgrade later. Had no problems going in to bios and changing the frequency from 2133 to the advertised 2666.


Western Digital M.2 240gb

Ridiculously easy installation, although I nearly lost the motherboard screw into the depths of the case. Read/write speeds are slightly underwhelming but not terrible - I may have gotten a slightly bad chip as I open some programs very slowly (Aorus Graphics Engine, Steam, MSI Gaming app) although that could just be the software's fault. Most of my files are installed here as I got a hard drive after finishing the build and haven't moved my files across yet.

WD Black 1TB Hard Drive

Can't say much, got it practically yesterday. Very easy installation and a bit of noise when booting up that wasn't there before - bigger than I expected but that was just me not knowing how big hard drives normally are.

Graphics Card:

Gigabyte Radeon RX 580 8GB

Received as a birthday present, the graphics power is certainly phenomenal and way outperforms my old Macbook Air (obviously). Unfortunately, I have a few things I don't like about this card - the software being ugly (subjective, it's orange and gamer-y) and clunky (buttons not responding, not many LED options), for one - and it can take around a full minute for the software to open after clicking the shortcut, but that could be a problem with the SSD.


Thermaltake Core V21

Very glad I went with this case. It wasn't easy to build in, as I spent upwards of 2 hours trying to figure out how to mount the Power Supply, and the motherboard was a little bit scary to install - but it was a good challenge. Most of my problems came from being inexperienced, and there being a lack of many good guides as to how to build in it. The manual was pretty useless in a lot of aspects, but thankfully I had the internet to help me. If I could give one piece of advice to anyone looking for builds on PCPartPicker that use this case and have intentions of building with it - Mount the Power Supply first. Seriously. I installed the motherboard first and it was a huge hassle to flip over the case and weave the wires through the sides with my whole arm in the case. Overall though, the case looks great, features optional horizontal motherboard mounting (the default configuration, I recommend this for beginners so you don't have to change things around) and the 200mm fan at the front is quiet and pushes a lot of air. The thermals are great, and the included dust filters are very useful. Certainly a top quality case, not to mention I got it for $20 off.

Power Supply:

Silverstone Strider Gold 550W 80+ Gold Fully Modular ATX

Does it's job. Was hard to mount in case, but not impossible. Quiet, and the wattage leaves room for upgrading my graphics card in the future if needed. If I could have changed anything in the build, I would've gone for a semi-modular PSU, so I didn't have to figure out which cables go in which slot on the PSU - which was funnily enough a lot more difficult than I expected. Worth noting, the actual connectors were worryingly stiff, I could not pull out the cables once I had plugged them in no matter what I tried. I plugged everything in correctly first try so it wasn't a problem - but I'd watch out for that in case it isn't just my model.

Wireless Adaptors

TP-Link USB adaptor

Plug-and-play, easy to use. A little unreliable but I used it until I could afford a PCIE wi-fi card, and now I leave it plugged in as a back-up wifi adaptor just in case. I get speeds of around 10 megabits per second download and 1 megabit per second upload.

D-Link PCIE adaptor

Saved up after PC was built to afford a much better wi-fi alternative, but was ultimately quite disappointed with this card. It does not fit securely into the slot once screwed in on the side, has stopped working twice, requiring me to reinstall drivers to get it working again - the speed is definitely good... when it works. I strongly advice getting a different adaptor if you can, but that being said, don't worry too much if you have this one already. It may or may not give you some trouble - but it's an easy fix most of the time.


Thermaltake Riing 12 RGB 120mm

Good fans, the controller is actually a plus for me because I didn't want to have to install software for the fans to work properly. The case allows me to very easily get into the internals to access the fan controller which is stuck with the included velcro controller to the inside wall of the case. The colour range is alright, it offers red, green, dark blue, white, yellow and off - but it also offers a rainbow mode where it cycles through 256 colours and you can press play/pause on the controller to stop it at any shade of colour you want eg. orange or pink. Worth mentioning these fans can't do purple for some reason, the colour cycle just misses purple all together. It can do light pink and light blue, but no solid purple.

To summarise, I am very happy with how it turned out, though it has been a stressful but rewarding experience. Very proud of myself for spending the day assembling a working computer at 15 years old after spending the last 6 months working late nights at McDonalds to afford it. I'd certainly like to thank /r/buildapc for all the advice in choosing out parts, and Kyle from Bitwit for his very in-depth tutorial on how to put everything together. If you have any questions, I'll answer them as soon as I can!

PS. I don't know about PC names, you guys can make suggestions in the comments if you want. Sorry for poor quality pictures, taken on an Iphone 4 and sent through email!

Part Reviews


Slower than I'd liked, but definitely 100x faster than a hard drive. M.2 is definitely worth the slight cost increase.

Wireless Network Adapter

Slow, but reliable - you get what you pay for. I use it as a backup wifi adaptor for when my PCIE wifi adaptor drops out.

Wireless Network Adapter

Works great, except when it doesn't.

Does not fit correctly in motherboard when screwed in, and does not screw in when correctly fitted to motherboard. Connection is fantastic, but drops out more often than I'd like (not the internet connection's fault, trust me).

I still use my ten dollar USB wifi adaptor as a backup because this card is so unreliable. If you've already bought it, don't worry - it's not the end of the world. But if you're thinking about buying it, do your research and get a more reliable card for the same price.

Log in to rate comments or to post a comment.


  • 28 months ago
  • 2 points

Congratulations on your very first PC!

  • 28 months ago
  • 2 points

Thanks! It's been a great experience.

  • 28 months ago
  • 1 point

My first ryzen arrived bent too, was it just one pin at the very corner?

  • 28 months ago
  • 2 points

Should clarify: the pin itself was not bent, just the corner of the metal lid with the ryzen logo. None of the pins were damaged thankfully.

  • 28 months ago
  • 1 point

Inside the case looks really good but a led strip or two might make it stand out visually if thats what ur into. Other than that sounds like to me you got really lucky with your processor still working and your ram being recognized by ryzen also bitwit is indeed awesome

  • 28 months ago
  • 1 point

Hi can you also add your benchmark score? and also fps score?? thanks

  • 28 months ago
  • 1 point

Sure, I'll get on to that in a couple hours when I'm free. EDIT: No I won't. I don't want to spend 20 dollars just to benchmark my computer, sorry.

  • 28 months ago
  • 1 point

Hey there, nice build! Could you further describe your pcie network not fitting properly? I am getting the same mobo and a pcie network card. Does the network card get in the way of the gpu cooling? Final question, If I used all the slots on the mobo (except for one 1x pcie under the gpu) would it all fit inside a cooler master lite 3.1? Thanks!!!!

  • 28 months ago
  • 2 points

As long as the cooler master lite 3.1 is a Micro ATX or larger case, a Micro ATX mobo will fit regardless of whether you use all the slots or not, you might want to check dimensions of your graphics card to make sure it fits in the case, and your CPU cooler in regards to your RAM to make sure your CPU cooler doesn't overlap on the RAM slots. The PCIE network card problem was due to the crappy model of network card, and not the motherboard. Even though the network card goes in front of the GPU, it doesn't hinder the cooling in any way.

Hope that answers your question!